S&S Cycle
SKU: SS106-5247
S&S Cycle SS106-5247 585GE Gear Drive Easy Start Camshaft Kit for Twin Cam 99-06
$1,940.00
Or 4 payments of $485.00 with 
Description
Description for S&S Cycle 585 Gear Drive Easy Start Cams Complete Kit
• Start any engine regardless of displacement or compression ratio with a stock starter• The new Easy Start Cams from S&S Cyclemake hard starting obsolete
• Heres how it works: Each of the two exhaust cam lobes are equipped with a spring loaded compression release lobe on the "heal" of the cam at the point where the valve would normally be fully closed, the lobe holds the exhaust valve open slightly at cranking speed, this releases some of the compression, making the engine much easier to crank , once the engine starts, and rpm increases, the compression release lobe is centrifugally retracted and the engine runs normally, with full compression, and without any loss in performance
• Allows a stock starter and battery to start nearly any engine
• Don't get caught "dead" without them!
• Centerline Intake: 102.5°
• Duration Exhaust @ .020: 260°
• Grind: 585C
• Lift @ Top Dead Center Intake: .186"
• Duration Intake @ .020: 245°
• Lift @ Top Dead Center Exhaust: .179"
• Lift: .585"
• Valve Timing Exhaust: 60°/20°
• Centerline Exhaust: 110.0°
• Valve Timing Intake: 20°/45°
Product Specs for S&S Cycle 585 Gear Drive Easy Start Cams Complete Kit
| Centerline Exhaust: | 110.0° |
|---|---|
| Centerline Intake: | 102.5° |
| Duration Exhaust @ .020: | 260° |
| Duration Intake @ .020: | 245° |
| Grind: | 585 |
| Lift: | .585″ |
| Lift @ Top Dead Center Exhaust: | .186″ |
| Lift @ Top Dead Center Intake: | .179″ |
| Manufacturer Part Number: | 106-5247 |
| Sold in Units: | Kit |
| Valve Timing Exhaust: | 60°/20° |
| Valve Timing Intake: | 20°/45° |
| Warehouse Part Number: | SS106-5247 |
(SS106-5247)
Fitment
Fitment Notes & Exceptions
- Installer must check for coil bind, valve-to-valve clearance, and valve-to-piston clearance
- Due to inherent characteristics of gear-driven cams, you may experience greater valvetrain noise
- High-lift valve springs are required to run these cams in 1999-2004 models and may be required for other applications
**Please Note: The fitment information below has been generated as a guide and may not be 100% accurate. Please contact us if you require further assistance.
- Harley Davidson Dyna Convertible FXDS: 1999,2000
- Harley Davidson Dyna Low Rider FXDL/I: 1999-2005
- Harley Davidson Dyna Super Glide Custom FXDC/I: 2005
- Harley Davidson Dyna Super Glide FXD/I: 1999-2005
- Harley Davidson Dyna Super Glide Sport FXDX: 1999-2005
- Harley Davidson Dyna Super Glide Sport Touring FXDXT: 2001,2002,2003
- Harley Davidson Dyna Wide Glide FXDWG/I: 1999-2005
- Harley Davidson Electra Glide Classic FLHTC/I: 1999-2006
- Harley Davidson Electra Glide Standard FLHT/I: 1999-2006
- Harley Davidson Electra Glide Ultra Classic FLHTCU/I: 1999-2006
- Harley Davidson Road Glide FLTR/I: 1999-2006
- Harley Davidson Road King Classic FLHRC/I: 1999-2006
- Harley Davidson Road King Custom FLHRS/I: 2004,2005,2006
- Harley Davidson Road King FLHR/I: 1999-2006
- Harley Davidson Softail Deluxe FLSTN/I: 2005,2006
- Harley Davidson Softail Deuce FXSTD/I: 2000-2006
- Harley Davidson Softail Fat Boy FLSTF/I: 2000-2006
- Harley Davidson Softail Heritage Classic FLSTC/I: 2000-2006
- Harley Davidson Softail Heritage FLST/I: 2006
- Harley Davidson Softail Heritage Springer FLSTS/I: 2000,2001,2002,2003
- Harley Davidson Softail Night Train FXSTB/I: 2000-2006
- Harley Davidson Softail Springer Classic FLSTSC/I: 2005,2006
- Harley Davidson Softail Springer FXSTS/I: 2000-2006
- Harley Davidson Softail Standard FXST/I: 2000-2006
- Harley Davidson Street Glide FLHX/I: 2006
Specifications
Reviews
Be The First To Review This Product!
Help other EasyR Australia users shop smarter by writing reviews for products you have purchased.
